Singer CD Player ACC 31 User Manual

MODEL ACC-31  
6-DISC CD CHANGER WITH  
WIRED COMMANDER  
COMPACT  
DIGITAL AUDIO  
INSTALLATION MANUAL  
 
BEFORE INSTALLING THE UNIT  
Transport Lock Screws  
The mechanism in the CD changer is "locked" into place during  
shipmentbythe4transportscrews,twooneachside. Besuretoremove  
thescrewspriortoinstallation.Retainthesescrews for futureusewhen  
transporting the unit for service/maintenance.  
CAUTION  
Afterremovingthetransportlock screws,placethesuppliedsealsover  
thescrew holes. Thesesealsareusedtokeepdustoutoftheunit,which  
could cause a malfunction.  
Installation and Wiring Precautions  
To prevent a short-circuit,  
l Be sure to turn off the ignition and remove the negative (-) battery cable, prior to installation.  
l Connect power wires last.  
1
NOTE  
If the changer is to be installed in a car that is equipped with an on-board drive or navigation computer, do not disconnect  
thebatterycable. Ifthecableisdisconnected,thecomputermemorymaybelost. Undertheseconditions,useextracaution  
during installation not to cause a short circuit.  
Do not install the unit in the following locations:  
l Locations exposed to direct sunlight.  
l Where hot air is discharged from the car heater.  
2
l In areas subject to extreme temperatures.  
Incorrect installation can cause the CD Changer sound to "skip" when playing  
a disc. Mount the unit firmly in place, using the supplied brackets and screws.  
3
Be careful not to damage the car wiring.  
4
l Be sure to use the supplied screws.  
l Be careful not to snag any wires when tightening screws.  
l Do not use any of the screws that are part of the brake or steering system to install the unit.  
5
l This unit cannot be installed on its side, end, or upside down. Installation in such positions will cause malfunctioning  
6
of the mechanism.  
3
 
INSTALLATION  
The unit can be installed horizontally (position H), or vertically at a 90° angle (position V). The position of the built-in anti-vibration  
springs (left and right side), must correspond to the mounting position chosen. If the springs are not set correctly for the type of  
installation chosen, the anti-vibration compensation will not be effective and vibration may cause the disc to skip.  
VERTICAL INSTALLAITON  
Set the anti-vibration springs to  
position "V".  
HORIZONTAL INSTALLATION  
Set the anti-vibration springs to  
position "H".  
POSITION  
"V"  
POSITION  
"H"  
PROCEDURE FOR HORIZONTAL INSTALLATION  
1
Attach a mounting bracket to each side of the unit, using the  
hex head bolts and washers.  
Hexheadbolts  
and washers  
NOTE: Make sure anti-vibration springs  
are set to position "H" as shown  
A
C
C
3
1
above.  
D
IG  
M
IT  
P
A
A
L
C
C
O
A
T
U
D
IO  
C
6
C
D
D
IS  
I
S
N
C
G
H
A
E
R
BY AUDIOVOX  
Bracket  
Determinethemountinglocation anddrilltwomountingholes.  
2
3
NOTE:If mounting surface is carpeted, use caution  
when drilling holes to prevent drill bit from  
catching on carpet. Cut holes in carpet  
before drilling into sub-surface.  
Carpet  
WARNING  
Never mount the unit near the fuel tank.  
Drill holes 1/8" (4mm) in diameter.  
Self-tapping Phillips head screw  
Secure the unit in place, using two self-tapping Phillips head  
screws.  
Use RTV (silicone sealer) on screw threads or around  
the holes to prevent moisture intrusion.  
A
C
C
3
1
D
IG  
M
IT  
P
A
A
L
C
C
O
A
T
U
D
IO  
C
6
C
D
D
IS  
I
S
N
C
G
H
A
E
R
BY AUDIOVOX  
Bracket  
4
Bracket  
 
PROCEDURE FOR VERTICAL INSTALLATION  
Note  
If the anti-vibration spring position has been changed and verified for vertical mounting (as shown on page 4), start with step 2.  
Set the anti-vibration springs to position "V"  
as shown below .  
Attach a mounting bracket to each side of the unit, using  
the hex head bolts and washers.  
1
2
POSITION  
"V"  
Bracket  
Bracket  
Hexheadbolt  
and washer  
Determinethemountinglocation anddrilltwomountingholes.  
Mount the unit in place, using two self-tapping Phillips head  
screws.  
3
4
Use RTV (silicone sealer) on screw threads or around  
the holes to prevent moisture intrusion.  
NOTE:If mounting surface is carpeted, use caution  
when drilling holes to prevent drill bit from  
catching on carpet. Cut holes in carpet  
before drilling into sub-surface.  
Self-tapping  
Phillips head  
screw  
WARNING  
Never mount the unit near the fuel tank.  
Bracket  
Bracket  
Carpet  
Drill holes 1/8" (4mm) in diameter.  
Hexheadbolt  
and washer  
5
 
VEHICLE COMPONENT LAYOUT  
NOTE:1.CheckwithyourRampage/Audiovoxaudiodealerto  
be sure your stereo is directly compatible with  
this CD changer.  
2. When used with Rampage Model AV-427 car  
stereo, besureChangerSelectorswitchonbottom  
of radio chassis is set to position "B".  
6
 
© 2000 Audiovox Electronics Corporation,  
Happauge, N.Y. 11788  
Printed in China  
128-5943  
8
 

Shark Vacuum Cleaner SV736 User Manual
Sharp Flat Panel Television LC 15B8U S User Manual
Shure Microphone PG52 User Manual
Snapper Chipper SG3000 User Manual
Sony Car Video System XR C6100W User Manual
Sony CD Player VGP XL1B User Manual
Sony Portable Radio SRF M37V User Manual
Southbend Fryer 45lb User Manual
Speed Queen Washer 18 30 lb User Manual
Swisher Trimmer ACR 500 ACR 500S User Manual